Sirsalliyan Small Air Compressor

Chicago Pneumatic Air

A New Concept of Square Air Fan

NISCO Fan Co. offers now a new design of a centrifugal general ventilating fan - Square Fan, in direct drive and belt drive configurations. Arrangement 4 direct drive square fans are ideally suited for a wide range of clean-air applications reuiring a tight footprint. Typical uses include pneumatic conveying, product drying, process cooling, and exhaust on clean-side of dust collection systems.

Some design features of the NISCO Square Fans include:

- Ten sizes from wheel size 10" to 30"
- Capacities up to 30,000 CFM airflow @ 20" WG pressure
- Choice of backward inclined, airfoil and backward curve wheel
- Four discharge configurations
- Narrow-width design permits higher speed and pressures

The following accessories are avilable:

* Clean-out door - available as a quick opening latch type door that swings open on hinges after cam levers have been turned, or flash bolted type with closely spaced studs to keep door securely sealed with Neoprene foam tape gasketing
* Shaft seals or Teflon shaft hole closures
* Outlet damper - single or multi blade, parallel blade or opposite blade designs, manually operated or complete with mounted electric or pneumatic actoator, for on / off or modulating air flow control
* Inlet screen
* Base rails with rubber-in-shear or spring type vibration isolators
* Inlet volume control with variable inlet vanes - external or nested in the inlet cone, for manual or automatic air flow control
* Housing drain - tank flange furnished in scroll of fans with down blast discharge, half couplings in housing drive side on all other discharges
* Spark resistant and explosion proof construction
* Safety drive guards
* Extended grease tube fitting
* High temperature fan construction with a shaft cooler assembly and high temperature paint
* Flanged inlet and outlet
* Stainless steel construction of SST 316, SST 304 or SST 347 stainless alloy are available for corrosive applications

NISCO Fan Co. Square Fans incorporate non-overloading BI impeller desings: the motor can be sized for the operating horsepower of the fan and not oversized, thus increasing motor efficiency. Heavy gauge spinning inlet with airflow diverter permits smooth air flow and close wheel tolerances.

Three different wheel designs on CB SQB Square Fans provide the widest choice in applications suitability, efficiency, sound, and cost. All of them feature the backward inlcinged non overloading horsepower chracteristic, where the horse power curve reaches a peak and then decreases even as air flow increases. This feature allows maximum brake horsepower calculation and motor selection that prevents electrical system overloading even if system pressure changes.

True aerodynamic airfoil blade shape allows stable operation from wide open to closed off; ideal for clean iar applications such as building ventilation with variable air volume system control or clean industrial gas handling. Aerodynamic single surface blade shape of backward curve wheel offers alternative selction points to the Airfoil wheel and also provides stable operation from wide open to closed-off. Flat, single thickness backwardly inlined plades are suited for applications from clean air to those where dust and limited material is present in the airstream and where airfoil shapes are not recommended due to material build up that closes unbalance and vibration.

For additional information please refer to http://nisco.net/custserv.html.

Oleg Tchechel
Canadian Process Air Systems Designer
NISCO Fan Co.
http://nisco.net/hvac.html
http://nisco.net/index.html

About the Author

Oleg Tchechel
Developer of Industrial Ventilation Equipment
NISCO Fan Co.

http://www.nisco.net/custserv.html

http://www.nisco.net/inquiry.html

Chicago Pneumatic Air Nibbler. Each $264.87 Manufacturer: Chicago Pneumatic. Each. Features Benefits: Strokes per minute: 2-1/4 lbs. - 1.0kg Avg. air consumption: 4 CFM Air inlet NPTF: 1/4" Min. hose size: 3/8" - 10mm Sound dba pressure: 93 - 103 Power vibration: 2.5 M/S2 Length: 7-1/2" - 190mm

Chicago Pneumatic CA147717 Repair Kit for Air Tools. Each $57.26 Manufacturer: Chicago Pneumatic. Each. 1 yr warranty on material and workmanship Customers also search for: Discount Chicago Pneumatic CA147717 Repair Kit for Air Tools, Buy Chicago Pneumatic CA147717 Repair Kit for Air Tools, Wholesale Chicago Pneumatic

Chicago Pneumatic Stylus. Each $30.22 Manufacturer: Chicago Pneumatic. Each. For writing and marking Tip Type = Chisel Bit Customers also search for: Discount Stylus, Buy Stylus, Wholesale Stylus, 015451127466, P054177, Air Hammer Chisels

Chicago Pneumatic Chisel. Each $22.14 Manufacturer: Chicago Pneumatic. Each. Tip Type = Bit Customers also search for: Discount Chisel, Buy Chisel, Wholesale Chisel, 015451132156, P084376, Air Hammer Chisels

Chicago Pneumatic Air Scribe Code Es. Each $366.27 Manufacturer: Chicago Pneumatic. Each. Air Consumption = 2.100 CFM Noise Level = 82.0 dB Vibration = 4.2 m/s2 Length = 5 in Inlet Size = 1/4 in NPT(F) Hose Size = 1/4 in Hose Control Type = On/Off Includes = Air Filter, Air Hose, Stylus Type = Engraver W

Chicago Pneumatic Cutter. Each $8.11 Manufacturer: Chicago Pneumatic. Each. Blade Shape = Wedge Blade Tip Shape = Straight Drive Size = 0.401 in Overall Length = 165 mm Tip Type = Chisel Bit Customers also search for: Discount Cutter, Buy Cutter, Wholesale Cutter, 015451081744, A046050, Air

Chicago Pneumatic Tune Up Kit for 797 Air Impact Wrench $81.95 Genuine Chicago Pneumatic parts help keep your air tool running in top condition

Chicago Pneumatic Repair Kit for 724 Air Impact Wrench $97.95 Genuine Chicago Pneumatic parts help keep your air tool running in top condition

Chicago Pneumatic Repair Kit for 734H Air Impact Wrench $78.95 Genuine Chicago Pneumatic parts help keep your air tool running in top condition

Chicago Pneumatic Tune Up Kit for 772H Air Impact Wrench $78.95 Genuine Chicago Pneumatic parts help keep your air tool running in top condition

Chicago Pneumatic Repair Kit for 772H Air Impact Wrench $230.95 Genuine Chicago Pneumatic parts help keep your air tool running in top condition

Chicago Pneumatic Tune Up Kit for 828 Air Ratchet Wrench $44.95 Genuine Chicago Pneumatic parts help keep your air tool running in top condition

Chicago Pneumatic Cut Off Air Tool. Each $68.02 Manufacturer: Chicago Pneumatic. Each. Features Benefits: Chuck size/wheel size: 2-7/8"- 73mm Weight 1-3/4 lbs. - Kg Length 7-1/4" - 181mm Avg. air consumption: 12.5 CFM Air inlet NPTF 1/4" Min. hose size 3/8" - 10mm Lock off throttle to prevent accide

Chicago Pneumatic Random Orbital Air Sander. Each $352.58 Manufacturer: Chicago Pneumatic. Each. Features Benefits: Paper size: 6" - 152mm Orbit: 10mm Dust collection: No Avg. air consumption: 6 CFM Air inlet NPTF: 1/4" Min. Hose Size: 3/8" 10mm Sound dba pressure: 79A Vibration: 2.5 Free Speed: 9500 RPM Moto

Chicago Pneumatic Mini Air Die Grinder. Each $68.27 Manufacturer: Chicago Pneumatic. Each. Features Benefits: Compact, lightweight design for easy maneuverability Lock off throttle to prevent accidental start up Complete with 1/4" and 6mm collet Built in regulator to match speed to the job Applications:

Chicago Pneumatic 1/4" Air Screwdriver. Each $353.25 Manufacturer: Chicago Pneumatic. Each. Features Benefits: External clutch adjustment Cushion clutch Built-in quick change chuck Handle exhaust directs air away from the work piece and operator Convenient forward/reverse valve General repair, body shops

Chicago Pneumatic 3/8'' Reversible Angle Air Drill $136.95 ? Compact, low profile head for drilling in confined areas ? Convenient reverse valve for simple directional changes ? Rear exhaust directs air away from the workpiece ? Teasing throttle for control from start-up thru run down ? Applications: screwdriving, drilling in hard to reach areas ? Free Speed: 1800 rpm Specifications: Chuck Size in.: 3/8 Weight lb.: 2-1/4 Length in.: 8-1/4 Aveerage Air Consumption CFM: 4 Air Inlet NPTF in.: 1/4 Free Speed rpm: 1800By Chicago Pneumatic.

Chicago Pneumatic 5 Air Angle Grinder. Each $272.34 Manufacturer: Chicago Pneumatic. Each. Features and Benefits Powerful .7 HP High Performance Motor provides power in all types of grinding conditions 5/8" - 11 Spindle - same disc size as present electric grinders 12,000 RPM maximum free speed gets the j

Chicago Pneumatic 1/2'' Air Impact Wrench $143.95 ? Differential regulator allows the operator to match the required power to the job ? Improved oil bath DYNA-PACT clutch delivers higher performance and extended durability ? Handle exhaust directs air away from the workpiece and operator ? Teasing throttle design for precise control ? Applications: overall automotive service, body shop, farm, light truck work, etc. ? Ultimate Torque: 425 ft.-lbs. Specifications: Square Drive in.: 1/2 Weight lb.: 5-1/8 Length in.: 7-1/2 Avg. Air Consumption CFM: 4 Air Inlet NPTF in.: 1/4 Working Torque Range ft.-lb.: 25-310 Ult. Torque @ 90 PSI ft.-lb.: 425By Chicago Pneumatic.

Chicago Pneumatic Hoistes Up-. Each $6143.11 Manufacturer: Chicago Pneumatic. Each. Self-locking worm gear stops load and holds it securely when air flow stops Operator speed control for precise load spotting Power vane motor provides positive high-torque starting characteristics All rotating parts

Chicago Pneumatic Engraving Pen. Each $72.93 Manufacturer: Chicago Pneumatic. Each. Features Benefits: Lightweight for easy operation Fine point stylus for precise engraving Cushion finger grip for comfort Low air consumption at only 1 CFM 14,000 blows per minute This engraving pen is lightweight

Chicago Pneumatic 1/4'' Reversible Air Drill - Compact $161.95 Chicago Pneumatic is pleased to introduce the reversible CP7300R 1/4'' Drill. Not only does it have the same great power as the CP7300, but now you can reverse it. With planetary gearing and brass bushings for great durability, this will be the last small drill you will ever need. With directional exhaust and rubber handle grip, this tool gives you comfort in any situation. The new forward reverse switch is small and out of the way to allow for comfortable handling no matter how you use the tool. If slow start drilling is what you?re after, this tool has all the trigger control you need. Great features, durability, style, and now it reverses. We just made the best small drill even better: ? 1/4 Horsepower Motor: Power to get even heavy duty jobs done quickly and easily. ? Speed: At 2,700 rpm this tool has the speed to get the job done fast. ? Compact and Lightweight: Get into even the smallest areas without a problem. ? Easy access Fwd/Rev Switch: Controls that are easy to access, but not in your way.By Chicago Pneumatic.

Chicago Pneumatic 3" Air Cut Off Tool. Each $153.93 Manufacturer: Chicago Pneumatic. Each. Features Benefits: Chuch size/wheel size 2-7/8" - 73mm Weight 1-5/8 lbs. - 0.7kg Length 7-3/4" - 197mm Avg. air consumption 5 CFM Air inlet NPTF 1/4" Min. hose size 3/8" - 10mm Rugged, energy-efficient 1/2 hp moto

Chicago Pneumatic 3/8" Square Drive Air Ratchet. Each $75.97 Manufacturer: Chicago Pneumatic. Each. Features Benefits: Std. bolt size: 3/8" (10mm) Weight: 2-1/4 lbs. (1.1 kg.) Length: 10-1/4" (257mm) Avg. air consumption: 4 CFM Air inlet NPTF: 1/4" Min. hose size: 3/8" - 10mm Sound dba pressure: 93A - 103 Vibrat

Chicago Pneumatic 3/8" Drive “Quiet” Air Ratchet. Each $221.26 Manufacturer: Chicago Pneumatic. Each. Features Benefits: Highest torque available on the market Working torque: 10-90 ft./lb at 90 PSI Maximum torque: 90 ft./lb at 90 PSI Motor: 0.5 HP Air consumption: 5 cfm Air inlet: 1/4 in. NPTF Min. hose size: 3/8

Chicago Pneumatic 1/2" Drive Heavy Duty Air Ratchet. Each $121.58 Manufacturer: Chicago Pneumatic. Each. Features Benefits: Square drive: 1/2" Std. bolt size: 3/8" / 10mm Weight: 2-5/8 lbs./ 1.2 kg. Length: 10" / 165mm Avg. air consumption: 4 CFM Air inlet NPTF: 1/4" Min. hose size: 3/8" - 10mm Sound dba pressure: 92

Chicago Pneumatic CPTKF138224 Air Tool Repair Parts Kits $61.3 Chicago Pneumatic KF138224 Blade Set 797 impact wrench. Huge selection to choose from. Using only the highest quality materials. Satisfaction ensured. Dimensions: 6 L x 2 W x 1 H.

Chicago Pneumatic Heavy Duty Air Die Grinder. Each $146.81 Manufacturer: Chicago Pneumatic. Each. Features Benefits: Rugged, energy-efficient 1/2 hp motor Built-in regulator matches speed to job Rear exhaust directs air away from work Square handle design for positive grip Applications: cleaning tire moldings,

Chicago Pneumatic 3/8" Air Reversible Angle Drill. Each $108.15 Manufacturer: Chicago Pneumatic. Each. Features Benefits: Compact, low profile head for drilling in confined areas Convenient reverse valve for simple directional changes Rear exhaust directs air away from the work piece Teasing throttle for control fr

Chicago Pneumatic 1/2" Heavy Duty Reversible Air Drill. Each $288.48 Manufacturer: Chicago Pneumatic. Each. Features Benefits: Teasing throttle for precise control Handle exhaust reduces noise and directs air away from operator and workplace Needle bearing gearing for improved durability Oil free operation Applications:

Chicago Pneumatic 3/8" Heavy Duty Reversible Air Drill. Each $218.74 Manufacturer: Chicago Pneumatic. Each. Features Benefits: Teasing throttle for precise control Handle exhaust reduces noise and directs air away from operator and workplace Needle bearing gearing for improved durability Oil free operation Free speed: 2

Chicago Pneumatic 3/8" Drive Light Duty Air Ratchet. Each $85.09 Manufacturer: Chicago Pneumatic. Each. Features Benefits: Working torque: 5-15 ft./lbs Maximum torque by hand: 30 ft./lbs Free speed: 220 Hose size: 1/4" Sound dba: 90.5 Extended length (7-3/4") Weight:1-1/8 lb. Avg. air consumption: 3 cfm This 3/8" d

Chicago Pneumatic 2" Air Angle Grinder. Each $146.49 Manufacturer: Chicago Pneumatic. Each. Features and Benefits: Compact and lightweight for easy access in tight areas Rubber handle grip for extra comfort Side exhaust directs air away from work area Self locking throttle prevents accidental start-ups Ful

Chicago Pneumatic 1/2" Drive “Quiet” Air Ratchet. Each $221.26 Manufacturer: Chicago Pneumatic. Each. Features Benefits: The Quiet One! As low as 79 dba! Unique, adjustable noise control with no loss of power - simply turn for quieter operation Highest torque available on the market Patented TriSpring ratchet hea

Chicago Pneumatic Super Duty Reciprocating Air Saw. Each $167.66 Manufacturer: Chicago Pneumatic. Each. Features Benefits: This premium cutting tool offers exceptional value while providing increased comfort, performance and durability. Ideal for body, exhaust and muffler work. Power at 10,000 strokes per minute allo

Chicago Pneumatic Super Duty Reciprocating Air Saw Kit. Each $227.44 Manufacturer: Chicago Pneumatic. Each. Features and Benefits: This heavy duty kit includes CP's 7901 reciprocating saw plus (5) each replacement blades: 18T, 24T, 32T packed in a heavy duty carrying case Lowest vibration on the market to reduce operator

Chicago Pneumatic 1/4" Drive Air Ratchet. Each $81.16 Manufacturer: Chicago Pneumatic. Each. Features Benefits: Working torque: 5-15 ft./lbs Maximum torque by hand: 30 ft./lbs Free speed: 220 Hose size: 1/4" Sound dba: 90.5 Extended length (7-3/4") - designed for greater reach in confined areas Weight:1-1